Kaffelogic Nano 7/LINK (D-P Serial) Power Cable Replacement

Escrito Por: Kaffelogic
  • Comentários: 0
Kaffelogic Nano 7/LINK (D-P Serial) Power Cable Replacement

Dificuldade

Moderate

Passos

10

Tempo necessário

10 minutes

Introdução

Replacement of the power cable on any Kaffelogic Nano or Nucleus Link coffee roaster with a D or P prefix serial number.

THIS GUIDE WILL NOT ALLOW YOU TO CHANGE YOUR ROASTER'S VOLTAGE SUPPORT!

  1. bEdI12xSfVQDKaCd
    bEdI12xSfVQDKaCd
    keWYfIuvFMvyWLWV

    • Remove the 6x 2.5mm Hex screws on the left and right side of the roaster.

    • Take care not to damage the buttons while maneuvering the front panel, with all six screws removed it may fall away.

  2. MhQ4bjGDjKieVDbY
    MhQ4bjGDjKieVDbY
    Nqrlq6TYIlRCEmPp

    • Hold the front panel steady while removing the plastic top/closure.

  3. JttMZ1MrHIv3w14y

    • Pull away the front panel carefully.

  4. xlnoDyLNHUxvifcH
    xlnoDyLNHUxvifcH
    BA3QijfXOOId6nAg
    3OUB1gVyYEkIiqKS

    • Remove the last 2.5mm Hex screw securing the rear panel.

    • Pull up on the rear panel to remove it from the roaster.

  5. id1Iu26FpOZgSFqK
    id1Iu26FpOZgSFqK
    bgPTsWYHJElkbeUh

    • Set the panels aside somewhere safe and bask in the beauty of your naked roaster.

  6. 1HnKYvo64HArJ5Th
    1HnKYvo64HArJ5Th
    JXsgGd5pwXe5ptsK
    VUJntB45IQEX5LEa

    • Remove the 2x 2.5mm Hex screws securing the cable carrier to the base.

    • Be careful not to lay the roaster on its front as the buttons can be damaged or broken off.

  7. iAHjGSrjeqBgE34S
    iAHjGSrjeqBgE34S
    wuoLO5ovFMhhv2jh
    JNPXUXEPiBmFAam5

    • Remove the terminal PCB cover and set it aside. This is held in with four small plastic clips at each corner.

  8. addW6rZEmXCsVLeC
    addW6rZEmXCsVLeC
    CD5PLFjT4EbOIlxB
    4QnaM25dEZXdHYlu

    • Disconnect the mains cables. Marked an N (Neutral) and L (Live)

  9. ViJs6lUFVJPFNKYg
    ViJs6lUFVJPFNKYg
    LokiDhSDTcB3KsPZ
    qNYRdkXSisgdkHoO

    • Remove the mains earthing connector from the tab. Pliers can be used for this as it can be tight.

  10. hZ1jQE6hsXPCmY1i
    hZ1jQE6hsXPCmY1i
    YfWpiT2uOuVT1lGw

    • Your mains cable is now free, and ready for repair or replacement.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Autor(a)

Kaffelogic

Membro desde: 23/07/25

2356 Reputação

0 comentários