Kaffelogic Nano 7/LINK (A/B/C-N Serial) SSR Replacement

Escrito Por: Kaffelogic
  • Comentários: 0
Kaffelogic Nano 7/LINK (A/B/C-N Serial) SSR Replacement

Dificuldade

Moderate

Passos

12

Tempo necessário

15 minutes

Introdução

Replacement of an SSR on any Kaffelogic Nano or Nucleus Link coffee roaster with an A, B, C or N prefix serial number.

  1. nfvSoTpnU4ksHcg6
    nfvSoTpnU4ksHcg6
    6MBXn1MgnMby6MAZ

    • Remove the 6x 2.5mm Hex screws on the left and right side of the roaster.

  2. qHiOtnAKcXjbaGoV
    qHiOtnAKcXjbaGoV
    OTbSwheRLDR1RpCH

    • Hold the roaster steady while removing the plastic top/closure.

    • Panels may spring apart slightly once removed.

  3. 5HgQGHsOcGRtWytG
    5HgQGHsOcGRtWytG
    YsnjyWOviUPEAgsT
    eljWHIrc23oQeaUH

    • Remove the 4x 2.5mm Hex screws on the bottom of the roaster.

  4. bokl2m3pNTLZsgaj
    bokl2m3pNTLZsgaj
    vu3RZpeDAwj1xhOk
    bUSiSNcKCwSERKhY

    • Pull away the front panel carefully.

    • Take care not to damage the buttons while maneuvering the front panel.

  5. CjFpLJRcjntXBWtF
    CjFpLJRcjntXBWtF
    U6CP2AwbVHaHnrnW
    Qasmpv1ohW2EYEcf

    • Stand the roaster up again and pull away the rear panel from the chassis to expose the remaining components.

    • The mains cable is routed through the panel and it will remain attached, place the panel in a soft bag if you wish to protect the paint throughout the rest of your repairs.

  6. FAnCybyJXrJcUBJK
    FAnCybyJXrJcUBJK
    eFeGmE2R5kswcjvW
    y2ngYWRQmp31aLF4

    • Disconnect the SSR signal lead and motor from the PCB-A

  7. KEsuURJd5jcMBDHC
    KEsuURJd5jcMBDHC
    Fh6WPRxKRW1JaEWO
    sQ5BEynWOyxvmMAN

    • Remove the 4x PH2 screws securing the gantry plate to the base.

    • Be sure to place the earth spade under the screw head when reassembling.

  8. iPHF4WiWL1lFN4CO
    iPHF4WiWL1lFN4CO
    31wrgwOlh6NoaUwq
    KrRCe24tvKRXMNZH

    • Tip the stack forward to gain access to the SSR.

  9. UgPHDLOnpZqAWSx1
    UgPHDLOnpZqAWSx1
    RWWNrTRQvVlHFE6U

    • Use a PH2 screwdriver to remove the trigger lead.

    • Note that this connection is polarized. Connect red/orange to (+) and black/brown to (-) markers on the SSR.

  10. ednpNXoC4LW6IIvK
    ednpNXoC4LW6IIvK
    2EXmoYk1b1qyGXBy

    • Use a PH2 screwdriver to remove the two mains spade terminals.

  11. 5uce1Hof46f3J4Qx
    5uce1Hof46f3J4Qx
    cDXu2qLVGBpOajvZ

    • Remove the 2x PH2 screws securing the SSR to the bottom of the gantry plate.

  12. E1hEXmeNLNE4WMk3

    • SSR can now be pulled out of the roaster and replaced.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Autor(a)

Kaffelogic

Membro desde: 23/07/25

2356 Reputação

0 comentários