Kaffelogic Nano 7/LINK (A/B/C-N Serial) Element Replacement

Escrito Por: Kaffelogic
  • Comentários: 0
Kaffelogic Nano 7/LINK (A/B/C-N Serial) Element Replacement

Dificuldade

Moderate

Passos

12

Tempo necessário

20 minutes

Introdução

Replacement of the element on any Kaffelogic Nano or Nucleus Link coffee roaster with an A, B, C or N prefix serial number.

  1. nfvSoTpnU4ksHcg6
    nfvSoTpnU4ksHcg6
    6MBXn1MgnMby6MAZ

    • Remove the 6x 2.5mm Hex screws on the left and right side of the roaster.

  2. qHiOtnAKcXjbaGoV
    qHiOtnAKcXjbaGoV
    OTbSwheRLDR1RpCH

    • Hold the roaster steady while removing the plastic top/closure.

    • Panels may spring apart slightly once removed.

  3. 5HgQGHsOcGRtWytG
    5HgQGHsOcGRtWytG
    YsnjyWOviUPEAgsT
    eljWHIrc23oQeaUH

    • Remove the 4x 2.5mm Hex screws on the bottom of the roaster.

  4. bokl2m3pNTLZsgaj
    bokl2m3pNTLZsgaj
    vu3RZpeDAwj1xhOk
    bUSiSNcKCwSERKhY

    • Pull away the front panel carefully.

    • Take care not to damage the buttons while maneuvering the front panel.

  5. CjFpLJRcjntXBWtF
    CjFpLJRcjntXBWtF
    U6CP2AwbVHaHnrnW
    Qasmpv1ohW2EYEcf

    • Stand the roaster up again and pull away the rear panel from the chassis to expose the remaining components.

    • The mains cable is routed through the panel and it will remain attached, place the panel in a soft bag if you wish to protect the paint throughout the rest of your repairs.

  6. LOUtgc2IXJRydMVn
    LOUtgc2IXJRydMVn
    SHRTLBYnb1fuvc6L
    ybX1iqscCSwVJJlm

    • Remove the 4x PH1 element chamber screws from the plastic bowl. (One screw not pictured)

    • When reassembling make sure there is no airgap indicated by the red and blue arrow

  7. BG6ZW3B2UQdhQ6FM

    • Set the roast chamber aside but do not disconnect any wires.

  8. oP4ZmfoYaKrFjqdc
    oP4ZmfoYaKrFjqdc
    MNmubFSDv6PlZDtN

    • Lift the element chamber up carefully to expose the element. Set this aside.

  9. GheWmCtpMTTyI31G
    GheWmCtpMTTyI31G
    Yc2HjZ3agnYnXXLn
    DKtQsNVEQISG5lkP

    • Lift up the element slightly and remove the support ring.

    • Do not touch the element coil directly. Skin oils can create hotspots on the wire.

  10. pWfwLdAhGZROWVHx
    pWfwLdAhGZROWVHx
    ArHPG6i4FxUUlFlR
    lffiKLPL4XOCrXeI

    • Use a flathead screwdriver to remove the element leads from the terminal block.

  11. 4bSh5MeT25BFkarD
    4bSh5MeT25BFkarD
    G1UZIXsLakSjMF3y
    pHJIlYtU41CH2vHe

    • Pull the element leads through the fibreglass tubing to remove the element.

  12. bJylX1MSdXomgjTf
    bJylX1MSdXomgjTf
    RQxMPA6sDfsV3bbe

    • Double check the cable position, so that the screw is coming down on the wire and not the insulation of the element.

    • Head through to our wiki for instructions on recalibrating your fan speed and element resistance after replacing the element. Nucleus Link anemometer instructions can be found here.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Autor(a)

Kaffelogic

Membro desde: 23/07/25

2356 Reputação

0 comentários