Geek Bar Pulse Teardown

Escrito Por: Greg
Publicado em: 07/06/24
  • Comentários: 19

Geek Bar Pulse Teardown

Publicado em: 07/06/24

Teardown

Introdução

How to disassemble Geek Bar disposable vaping unit.

  1. Til1S3fTY2WZScEa

    • Use a wood chisel (~1 inch) along the seam to break loose the clear cover. The cover snaps into place but may be lightly glued.

    I've taken apart several of these, and there's no glue; it's strictly a snap fit.

    Jerry Wheeler -

    I cannot push the on off up? To get case out?

    Sharen Larner -

  2. aZi5dqh5ccCEZ5WG

    • Pull out the internals. You will need to push in the on/off switch at bottom of unit to get the insides to slide out.

  3. xEHN5ZxquImnNkLw

    • Detach tank. Note location of wiring if you are going to reassemble unit.

  4. PVC6uxI6FqLyjOPQ
    PVC6uxI6FqLyjOPQ
    a5iCkZcHxyQuRZIV
    4NKAXBPHkd4jQRTc

    • Pull off top of tank.

    • Pull heater unit out of steel sleeve.

    • Remove flat wick from heater

    • Observe basket style heater unit. Resistance readings: blk-grn: 1.1 ohms; blk-red: 1.1 ohms; red-grn: 2.2 ohms

  5. L2sCXBlGwJ6ZnTES
    L2sCXBlGwJ6ZnTES
    kd3MElTWqQcGyV1D

    • Unsnap the circuit board from the L-shaped plastic holder.

    • View board.

    Well now, what the heck is this tiny little board! Anything cool on there, logic unit-wise?

    PCs After Dark -

  6. evQiXXN16NMUTPPJ

    • The lip piece can be unsnapped from the inside, pulled out from the top and disassembled as shown.

    I was looking for exact directions on the lip piece filter and rubber because the filter in mine has a film over one side and it’s just like cotton on the other. Does that go up or down inside the gasket or just on top of it when I took it apart mine hit the floor, so I have no idea. Thank you.

    Kelly Colle -

    Sorry, I don't recall how that little oval shaped piece was oriented. It doesn't appear to filter anything & maybe its used to seal the air passage going to the mouthpiece. That film may have been a piece of double sided tape used to hold it in place during assembly ... That is a guess.

    Greg -

    The filter is to help catch any stay fluid (juice) that may catch a ride past with coil/heater when you take a hit. The rubber piece is a seal. The rubber piece goes inside the mouth piece first, then the filter.

    Ichabod -

Autor(a)

Greg

Membro desde: 23/08/20

425 Reputação

13 comentários

Perfect illustration and pics.

Leo Arakel -

Hell yeah thank you

zzaqd -

love u man, sooo much

Emran Shafaq -

So satisfying. Now it's a perfect secret-stash container too!

PhoenixEd -

I used this to open it and fix an auto-fire/over-fire I was experiencing. I've had it happen before but simply cannot afford to buy another. After opening, I powered it on, hit it & it hit fine. I then switched it off, put the switch cover back on, hit it and back to auto/over-firing again. I removed the switch cover and it was fine, closed it back up without the switch cover and it hits fine, pulls more air in, but I am thinking based off my understanding of vaping herbs that a faster, higher airflow willl create a lower temp & therefore, it shouldn't use up as much fluid per use even tho I have it set to pulse mode. This won't effect the fluid guage as it's predetermined and even if you add fluid while at say 60%, it will not change the level shown or the amount it displays. I'm used to having them display 0% and having several days of full flavor/hits even after this. Thanks for the breakdown, clean, simple, easy to understand. I've opened the Pulse X but never one like this, so thanks.

EROCK611 -

Thank you so much this is going to help me with one of my projects.

Prince Doge -

541125040653

Alee Sg -

I dropped mine the water and now it’s not working so I’m putting the juice part in my other one that’s just hit 0

Cali -

I pulled it off and accidentally popped the wires out, can anyone show me which color goes where if possible?

Parker -

If you mean the red, green and black heater wires, there's a picture in the teardown showing where these wires go in the silicon lid. I think you can make out the colors.

Greg -

Mon petit frère avait introduis une tige dans ma puff du meme modèle depuis elle marche mais la fumer ne passe plus

Nathanaël Benard Mabonzot -

In my experience the 'internals' won't budge unless you remove the mouthpiece first. That and the little cap on the on/off switch.

Amandathebrabe -

Getting the internals to slide out takes some force. This unit came apart with some difficulty. Took one apart around 10/2025; more difficult to disassemble. Could not remove mouthpiece without removing internals first.

Greg -