WowWee MiP Robot Power Switch Replacement

Escrito Por: Daniel Burkholder
  • Comentários: 2
WowWee MiP Robot Power Switch Replacement

Dificuldade

Moderate

Passos

10

Tempo necessário

30 - 45 minutes

Introdução

The power switch turns the MiP on or off. If it's malfunctioning the robot will not work.

  1. iUngOsHkGDJuNdcg
    iUngOsHkGDJuNdcg
    mbPtI1McjuEwTSM2

    • Remove the three 12.0 mm Phillips # 2 screws from the battery cover.

  2. NqkVBAHBS5kZHQNf
    NqkVBAHBS5kZHQNf
    GaoNIPBQABdnSmVg

    • Carefully pull the battery pack from the robot.

    • Remove the batteries from the battery pack.

  3. ShHZaoFaVfGIcOpE
    ShHZaoFaVfGIcOpE
    gRck2QqL1BgcAgaL

    • Use a metal spudger to carefully pry off the hubcap without marring the plastic wheel or hubcap.

    • This plastic material is not replaceable. Any damage will be noticeable.

    The hubcap won't come out. It's flat & tight. Even a tiny screwdriver for eyeglass repair can not get under it. Any tricks forgetting it out?

    donna.hester7 -

  4. Vw1biTfGQB2ytDTy
    Vw1biTfGQB2ytDTy
    sYNdOfABTm1aOeEL

    • Remove the 12.0 mm Phillips #2 screw.

    • Hold the wheel in place, or it will rotate as you attempt to remove the screw.

  5. LjtN3AW5hM5dY5xG

    • Pull the wheel off of the square axle.

    • Do not use excessive force while removing the wheel. Pulling too hard on the wheel can damage the axle.

  6. QRE1AV5hMaBMVaSW
    QRE1AV5hMaBMVaSW
    DgPR3wiOABFgfO62

    • Remove the eight 9.3 mm Phillips #1 screws from the back of the robot.

  7. MXIY2QcErJJkWeJa
    MXIY2QcErJJkWeJa
    rExo3TPTffKKS2I4
    wj21NxCUX42JNiP2

    • Remove the arms from the body.

    • Carefully open the body compartment.

    • Open the compartment slowly. There are wires connecting the two body pieces together. If pulled too hard, the wires and/or the motherboard could be damaged.

  8. 4HBDLMgoWCHrQC1t

    • Using precision tweezers, disconnect the following three bundles of wires:

    • Connecting the battery pack to the motherboard.

    • Connecting the power switch to the motherboard.

    • Connecting the speaker to the motherboard.

  9. EXWFiI2nmEZoW1ay
    EXWFiI2nmEZoW1ay
    AVBACASEBSNSIxLe

    • Remove the two 9.3mm Phillips #1 screws.

  10. 5kObKlMgHIVjtRre

    • Remove the power switch assembly from the body by gently pulling straight out on the wires.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Autor(a)

Daniel Burkholder

Membro desde: 16/02/16

623 Reputação

Um comentário

where can i buy the power switch of MiP

Reinejoe Cacho -