Sony Walkman D-EJ360 Motherboard Replacement

Escrito Por: Adam Hutchinson
  • Comentários: 0
Sony Walkman D-EJ360 Motherboard Replacement

Dificuldade

Moderate

Passos

9

Tempo necessário

10 minutes

Introdução

This guide will inform you on the steps required to remove the motherboard from the Sony Walkman D-EJ360. The motherboard is the central electronic component that interacts with all of the other components on the device. If your device is not powering on, not producing sound, or facing other issues, replacing the motherboard may be a key step in returning functionality to the Sony Walkman. The motherboard is moderately difficult to remove as it requires all non-soldered components to be removed beforehand. The motherboard is a sensitive electronic. The use of an ESD strap is highly recommended.

  1. YljcLHNTSUH3qLaS

    • Open the lid on the Walkman by pressing the open button on the device.

  2. FBCmOfFuYVaXoEtr
    FBCmOfFuYVaXoEtr
    ZQ6jOWMeCKnSUjkJ
    rYeQdn4tI2IjYdaV

    • Grip the thin end of each spring using a pair of tweezers, slide it out of the lid notch, then press down on the main coil to release and remove it.

  3. aBMcyn3pUD2qGsIk
    aBMcyn3pUD2qGsIk
    IGoNjI5SixER5OgN
    TeM5fFPiBc4sluBM

    • Insert the metal spudger in the crevice between the blue lid and the white body of the Walkman.

    • There is a notch where the lid is held under to stay in place. With the spudger, push the blue lid portion down and out.

    • This may require some harder force. You will hear a popping sound when you successfully push the lid out under the notch.

    • Repeat the same tactic on the other side. The other side should become easier to pop off.

    • Remove the lid.

  4. 6gsjaOHSISYbYnIC
    6gsjaOHSISYbYnIC
    vi3kAEaFJBEgjQVc

    • Remove the eight 6.1 mm screws using a Phillips #00 screwdriver.

    • Open the battery cover to reveal the last screw.

    • Remove the ninth 6.1 mm screw using a Phillips #00 screwdriver.

  5. FT5dmVYZhfwRdkPQ
    FT5dmVYZhfwRdkPQ
    4J6WrSIFmRlXZyUL

    • Insert a Jimmy into the seam between the upper and lower cases and pry apart.

    • Avoid initially prying near buttons, or the laser assembly.

    • Pry until the there is an audible click. The halves should visibly separate roughly 1/4 in.

    • Work around the seam in a circular path, separating the halves completely.

    • The motherboard and turn table module are only held in by gravity in the blue shell. Do not tip the device while separating the shells.

  6. 4MXYPalCAQxKkBKd
    4MXYPalCAQxKkBKd
    CQJiGa5MAlgPFsLe

    • Using tweezers, gently lift the the locking flap on the laser module ribbon connector.

    • Gently remove the ribbon cable from the connector.

  7. IqSSoGl13fYAjeZq
    IqSSoGl13fYAjeZq
    CLLPARSWRkJibQFS
    T66g4GoUZWidYLMJ

    • Using tweezers, squeeze the upper half of the four wire connector, and lift straight up to remove the connector.

    • The connector may make a tactile click when disengaged.

    • Repeat the step for the two wire connector.

  8. n1Og3RgICqVkWojh
    n1Og3RgICqVkWojh
    gMOGC4oQcfpOSTws

    • Ensure the ribbon cable, two, and four wire cables are all removed and not tangled with the motherboard.

    • Gently lift the laser module and place aside.

  9. WZICg3m62LZakDKU
    WZICg3m62LZakDKU
    JFhFTKSUrDk2XNYU

    • Lift the board on the same side as the battery terminals, and slide the board out diagonally.

    • The audio jack will be constrained vertically by the lower cabinet. Use care when trying to remove the board.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Autor(a)

Adam Hutchinson

Membro desde: 22/10/25

73 Reputação

0 comentários