Panasonic SA-PM17 Tape Player Unit Replacement

Escrito Por: NathanB
  • Comentários: 2
Panasonic SA-PM17 Tape Player Unit Replacement

Dificuldade

Moderate

Passos

11

Tempo necessário

30 - 50 minutes

Introdução

This repair guide will show you how to replace the tape player unit of your Panasonic SA-PM17 by tearing down the device to the point where you can take the unit out and put a new one in.

  1. UXeV6UTrAjrgcVWM
    UXeV6UTrAjrgcVWM
    6PU2ZRGvfvwlo4NS

    • With a Phillips #0 screwdriver, remove the eight 9.5mm screws attached to the left and right panels of the device.

  2. INGZ4heN5dNHgQON

    • With a Phillips #0 screwdriver, remove the five 11.5mm screws attached to the backside panel of the device.

    • Organize and label screws into a Ziploc bag for an easier resemble process.

  3. Py5ISLnOSxCTDrNd

    • Detach the right and left panels from the device.

  4. peyt6cuJRtKfVpSG

    • Lift the top panel and gently place alongside the device.

    • Allow the top panel to rest on the back without reattaching it.

    • CAUTION: Do not extend the top panel too far from the device due to the connected wires.

  5. DmYng6Be3euY6Zws
    DmYng6Be3euY6Zws
    wQDlPFmhBmaLmuwn

    • With the tweezers, detach the indicated tabs from the hooks by lifting upward.

    • Disconnecting the tabs will release a portion of the front panel connected to the entire device.

  6. gHuEreWGeDYD53mS

    • Lift the top panel upward while firmly sliding it towards the back of the device.

    • CAUTION: Do not extend the top panel too far from the device due to the connected wires.

    • The wires connected to the top panel will need to be disconnected in order to completely detach the panel.

  7. 55WFomEBHRhUw2oK
    55WFomEBHRhUw2oK
    tIfNEODcJJlqjM4r

    • Disconnect the black wire by gripping the wire at the base and pulling gently until released.

  8. GvhaL6WbPocJqWAJ
    GvhaL6WbPocJqWAJ
    ii6mEsNeeFZvNIgs
    qXVumpZms6cSGlTx

    • This step deals with the indicated area of the device.

    • Using the tweezers, detach the indicated tabs so that the cord may be released from the restraints.

    • Gently pull on the cord, near its base, until it comes free of the restraint.

  9. D3Q5IWMTsCtLQYVM
    D3Q5IWMTsCtLQYVM
    X341WvT6hoEPLogc
    LkNw4PPuHobjxhZl

    • This step deals with the indicated area of the device.

    • Lift the indicated tabs out until the restraint looks like the final picture.

    • Gently pull on the cord until it is released from the attachment.

    • The top panel is now disconnected from the device.

  10. 2m4iZH3LvbuRalYM
    2m4iZH3LvbuRalYM
    jwO4KnbLMgBpmOHX

    • Remove the four 12.1mm screws using a Phillips #0 screwdriver.

    • Organize and label screws into a Ziploc bag for safe keeping and easier resembling process.

  11. NvS61gK3X5yhqXwI
    NvS61gK3X5yhqXwI
    DJgWRGhxReY5DXXG
    gR163pLlBYhc2tjI

    • This step deals with the indicated area.

    • Using the tweezers, pull the indicated latch to the right to disconnect the tape player unit from the top of the device.

    • While holding the latch to the right, lift the unit up from the plastic.

    • CAUTION: When the latch is disengaged, the tape cover may push out and force the rest of the apparatus to pop up. This is normal, but be careful that the tape cover does not pop out too quickly.

    • NOTE: When placing this unit back on the device, you can simply push the unit into position. The latch will automatically snap into position.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Autor(a)

NathanB

Membro desde: 13/04/11

418 Reputação

2 comentários

The problem with my micro system pm17 is that the tape drive's head does not work. I noticed that it is a gear that has the function to trigger,The gearbox has probably moved out of its original position and is now not turning the read head.How do I return the gear to the original position so that it re-engages the bedhead?

Rogerio -

Add a comment

The problem with my micro system pm17 is that the tape drive's head does not work. I noticed that it is a gear that has the function to trigger,The gearbox has probably moved out of its original position and is now not turning the read head.How do I return the gear to the original position so that it re-engages the bedhead?

Rogerio -