Nissan Rogue 2016 Engine Air Filter Replacement

Escrito Por: OGentil
  • Comentários: 0
Nissan Rogue 2016 Engine Air Filter Replacement

Dificuldade

Easy

Passos

10

Tempo necessário

10 - 20 minutes

Introdução

Changing the air filter in your Nissan Rogue 2016 will ensure that the air intake for the engine is pure and without debris that could damage it.

This guide will show you how to quickly accomplish this task. You will need to have the replacement filter, 10 minutes, and not be afraid of getting your hands dirty.

Before using this guide, make sure the engine has been turned off long enough to cool down.

  1. yZTVb3QQpLF2hgqD
    yZTVb3QQpLF2hgqD
    2aNLCJSiCVlvIGLA
    2gRvy3ngtlm1jEwU

    • Use your finger to pull the hood lever on the driver’s side, near knee level, to open the hood.

    • Under the hood, find the latch that holds the hood. Push it to the side to allow popping up the hood fully open.

    • Pop the hood stick (it is held under the hood) and place the end that is not connected to the hood in the hole in the chassis. Ensure it properly fits the hole, and the hood is securely in position.

  2. PYQWUpGxZG6IsP2N

    • Locate the filter housing, just behind the battery.

  3. 2eLbdMkN4WSCJHsN
    2eLbdMkN4WSCJHsN
    gvoDWL2kPFOvjqDZ
    Mma4VuSmAeNrVbwR

    • Release the clips at the front of the air duct.

    • Press it down a bit to make it easier to release.

    • Release the clip in the back. It should come loose as you move the duct towards the back.

  4. wh6HO16Te2YoWTbA

    • Remove the duct.

  5. gHqpULElDjOktZGD
    gHqpULElDjOktZGD
    NSLgWBlmFe2AGVtU

    • Release the fasteners of the filter housing. Move your finger to the back of the fastener and pull outwards.

    • Repeat on the other side.

  6. gkEiGPVxnMbhGYnS
    gkEiGPVxnMbhGYnS
    1BgkTGtSnTlYDS6k
    WVkGNQEcUALINxVr

    • Pull the top of the filter toward you and lift it out of the housing.

    • Insert the new engine air filter.

    • The top of the filter has a small lip to ensure it is installed in the correct orientation.

  7. fZAKWMyQmeXlRuma
    fZAKWMyQmeXlRuma
    SainCBEYbFllGobH

    • Press the front of the housing back in place and engage the fastener on one side.

    • Repeat the process on the other side.

  8. nhiNDw5Aat1CwDda
    nhiNDw5Aat1CwDda
    rASrPDYIbWyGHqUF
    bXCVqXLnAhAOmWNR

    • Slide the back of the duct onto the filter housing.

    • Ensure the clip in the back and the duct are aligned and fit in place.

    • Secure the clips in the front of the duct.

    • You might need to work on one side at a time.

  9. cvDFEtvJUbArb6jW

    • Check that the duct is securely seated in place.

  10. lPIvNcU4uHUrSZuX

    • Make sure you did not leave anything under the hood (keys, tools, etc.)

    • Push the hood up slightly, and release the hood stick from the chassis.

    • Secure the hood support rod in place against the hood.

    • To close the hood, move yourself back a bit, lower the hood, leaving at least a foot from closing. Drop it.

    • It should lock in place. If not, pop it back open and let it fall from a bit higher distance. Don't press the hood down to lock. It could dent the hood.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Autor(a)

OGentil

Membro desde: 02/11/25

181 Reputação

0 comentários