Mission Hammr Bow String and Cables Replacement

Escrito Por: Mathew Reed
  • Comentários: 1
Mission Hammr Bow String and Cables Replacement

Dificuldade

Moderate

Passos

9

Tempo necessário

30 - 45 minutes

Introdução

This guide will show how to replace the strings and cables on a Mission Hammr archery bow.

Before attempting this make sure you know how everything being used for the repair operates. Incorrect use of the equipment could lead to damage and potential injuries to you as well.

When compressing the bow in the press be sure NOT to compress it anymore than what’s needed. If you do, it could result in damage to the bow and the bow press itself. If compressed enough the bow could shoot out of the press potentially harming you as well. Make sure the arms you are using in your bow press are supported in working on the Mission Hammr. If your press is not capable of holding the Mission Hammr DO NOT attempt to work on this bow in your press, doing so can seriously harm you and the equipment. Keep your fingers out of the cams. This can be tough when trying to replace the strings and cables but remember the bow is compressed and if it was to slip out while you had your fingers in them, they have the ability to break or cut off your fingers.

Warning: Exercise extreme caution when following this guide. Do not attempt to work on this bow in your press. Doing so can cause serious injury.

  1. QfNaMBJYlFReiYDC

    • Begin by aligning the small, grey arms of the bow press with the limbs of the bow.

    • Make sure both the bow press and the bow are safe to use with this particular bow.

  2. VOOKZwA2LMwPZIeW

    • Slowly compress the bow press until the string has some slack, as shown in the picture.

    • Do not compress the bow any more than necessary, as this could damage the bow or the bow press.

  3. lRVtpHVykVyrmGR1

    • Before removing the string or cables, note where each component goes for reassembly. Take a photo if needed.

  4. QAYRa6YqRsAXF6Sa

    • First, carefully remove the string.

    • The string is the easiest part to remove and reinstall, and taking it off first keeps it out of the way while you work on the cables.

  5. yV3fySb3NFTMFZIt
    yV3fySb3NFTMFZIt
    3MOD5UdcueBwNpqy
    OUaKJmpqMUhIFNAW

    • Remove the cables one at a time.

    • After removing each old cable, immediately replace it with the new one to ensure correct placement.

    • The cable hooks onto the cam at the point labeled C.

    • The string attaches at the point labeled S.

  6. WHnsEv6pStMRMFwi

    • Once both sets of cables are replaced, double-check that they sit correctly in their grooves before proceeding.

  7. EH4JLInYXAdSyaEq
    EH4JLInYXAdSyaEq
    aSEplNX2GqwQWYsu

    • Finally, replace the string.

  8. pvKL6EDUVqyqxs5V

    • Now with the string on and in the correct groove check through everything once more.

    • With the bow press, slowly tighten the strings and cables until it looks like it did before the replacement.

    • Use your before picture for a comparison to make sure it's correct.

  9. PlKDUD2nCh5ZCpMf

    • Now with the pressure back on the bow everything should be ready to go.

    • Double check to make sure the cables align in the tuning holes and the strings and cables have successfully been replaced.

    Hey any change you can post a pic of the cams from the top where the y-cable attaches to the cam. I just picked up a hammr myself but I think the cam is bent, but I'm not sure because both cams have this slight bend at the same spot.

    Rob K -

Conclusão

To reassemble your device, follow these instructions in reverse order.

Autor(a)

Mathew Reed

Membro desde: 24/03/21

187 Reputação

0 comentários