Lenovo Yoga 910-13IKB Fingerprint Reader Replacement

Escrito Por: Nikki Sorfleet
  • Comentários: 2
Lenovo Yoga 910-13IKB Fingerprint Reader Replacement

Dificuldade

Easy

Passos

12

Tempo necessário

10 - 15 minutes

Introdução

Follow this guide to replace the fingerprint reader in your Lenovo Yoga 910-13IKB. If you have ensured that the finger you are trying to sign in with has been properly registered and the reader is clean of any grease or debris, but the reader still fails to correctly recognize your finger, it may need to be replaced. While this replacement is one of the longer ones in terms of time for this device, it is still quick and easy to do, requiring only a JIS #00 screwdriver.

  1. RfTaUpdHwPCCKsOm
    RfTaUpdHwPCCKsOm
    BGNEUIeRKcfEbBWd

    • Before you begin, be sure to turn off your laptop and unplug it from the outlet.

    • Turn the laptop over and remove the ten Torx T5 screws along the perimeter of the bottom panel.

    • Remove the panel.

  2. NTAL2eC6ZprHYJyZ

    • Use a Phillips screwdriver to remove the four M2 x 1.7 mm screws securing the battery to the laptop.

    • Remove the battery.

  3. C2eWWMOJjHUwmnyT

    • Remove the six Phillips screws that attach the trackpad to the device.

    • Use a spudger to disconnect the ribbon cable connector from the trackpad.

    • Remove the trackpad using a spudger.

  4. LgqBbYkKKSpB1DMh

    • Use a Phillips screwdriver to remove six screws attached to the USB ports on both sides of the device.

    • Detach both ribbon cables attached to each USB port with a spudger, then detach the USB ports.

  5. cARJxEfmbPSPaI4N
    cARJxEfmbPSPaI4N
    OVFFMMWdluoLAHbZ

    • Use a small Phillips screwdriver to remove all single screw securing the SSD stick to the motherboard.

    • Slide the SSD stick from the port on the motherboard.

  6. LWIkFseQhbJL5GHJ
    LWIkFseQhbJL5GHJ
    FJmNeVR2KPqBSiIQ
    WCjYqJOP3ufMfoZt

    • Use a small Phillips screwdriver to remove four screws from the fans.

    • Remove the back connector strip using a spudger to pry it off of the device.

    • Remove the fans.

    • Now, only the bottom panel should remain.

  7. iIp5d1lkTsrTaTFP

    • Remove the four 3 mm Phillips #0 screws holding the battery in place.

  8. BCIgxPVZHo1JFP1e
    BCIgxPVZHo1JFP1e
    XTeY1iFJAdgyoFNU
    p3vbWWq2dFXWAiNq

    • Disconnect the battery cable from its motherboard socket by gently pulling it towards the battery. The spudger tool may be needed to lift the flap seal.

    • Pull parallel to the battery, not straight up.

    • Pull evenly on the width of the cable so that no individual wire is overly strained.

    • Lift the battery out.

    This was perfect for me.

    Thanks!

    Larry Doughan -

    I thought I needed to lift the silver thing in order to pull it out, and the silver thing broke off.

    JENNIFER M -

  9. UoxYPQDTIDpjAegO
    UoxYPQDTIDpjAegO
    CAbhPyWNf2YRXyHq

    • Remove the one 3mm JIS #00 screw on the right side of the silver component.

  10. YZFeLXXYuqOcyDIY
    YZFeLXXYuqOcyDIY
    rkpXjlcqrJ5qREfa

    • Gently pull up on the ribbon cable to detach it from the metal housing.

  11. yEeKpwhYb3PrpJZA

    • Lift the metal housing out and set it aside. This component holds the reader in place.

    • The left side of the component is tucked under the lip of the computer, so lift from the right side of the component.

  12. BYonvsoPkDsCjbQV

    • Remove the fingerprint reader from its place.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Autor(a)

Nikki Sorfleet

Membro desde: 23/01/20

175 Reputação

0 comentários