LG env2 vx9100 Front Keyboard Replacement

Escrito Por: Reed Williston
  • Comentários: 0
LG env2 vx9100 Front Keyboard Replacement

Dificuldade

Moderate

Passos

10

Tempo necessário

10 - 15 minutes

Introdução

In this guide you will be removing the front panel from the rest of the phone to access the front keyboard.

  1. FDNQgTXsc2rg4SqX
    FDNQgTXsc2rg4SqX
    HmIshFJKhLHZkoK3
    bHI3bcbXeAadIBkH

    • Power off the phone before disassembly to avoid electric shock or fire.

    • Place the phone face down on the table.

    • Pull down the tab below the battery with your fingernail or an opening tool.

    • Lift the battery out.

  2. wTAu3hi3iFZQY2Mp
    wTAu3hi3iFZQY2Mp
    UYXeBgMIaYnMyh2y

    • Use a metal spudger to remove the five rubber covers and expose the screws underneath.

  3. iAbokJEanyQkewnD
    iAbokJEanyQkewnD
    eRMtiQmIN5m6Kqtf

    • Remove all six 2.5 mm screws with a Phillips #00 screwdriver.

  4. UpDV4DW2BwZu2eSE
    UpDV4DW2BwZu2eSE
    cIDbSIawhUfGoBrm

    • Insert a plastic opening tool into the seam and gently pry to release the tabs.

    • Work around the phone until all tabs are released.

    • Remove the back panel.

  5. YJwyLDRExWaKmERT
    YJwyLDRExWaKmERT
    pGJwVGjcfSpIRaCD

    • Use a spudger to pry the two rubber covers out of the device.

  6. I4EwWpip1iGECyT3
    I4EwWpip1iGECyT3
    iqAXVZAaDeWR2bGq

    • Use a Phillips #00 screwdriver to remove two 2.5 mm screws.

  7. S5MXrXvIhUpe25nh
    S5MXrXvIhUpe25nh
    wMoypCnMSVQwLW2K

    • Use a Phillips #00 screwdriver to remove two 2.5 mm screws.

    • These screws will not be visible or accessible unless the two sides of the phone are at approximately 90 degrees relative to each other.

  8. cNamRGNNaBTbRwuw
    cNamRGNNaBTbRwuw
    ukee61rEIeUPDmOH

    • Insert the plastic opening tool in the crease and move it along each edge of the phone.

    • Separate the front panel from the rest of the phone.

    • Be careful not to damage the orange ribbon that connects to the motherboard through the hinge in the phone. If the ribbon is damaged, the phone will not function properly.

    • Open the phone to reveal the inside monitor.

  9. KPFUjT36gABsF6QD
    KPFUjT36gABsF6QD
    ZVSRFQAsGHDNfK1p
    cwPBZZ1BiHpHWZA1

    • Use a Phillips #00 screwdriver to remove two 2.5mm screws.

    • Using your hands, separate the front panel from the phone by carefully pulling it straight off.

  10. COgBaMgnfHpJO6UP
    COgBaMgnfHpJO6UP
    oufEkI6ZOZsMrfdP

    • Place the front panel so that the buttons face upwards.

    • Push on the buttons to remove the keyboard from the front cover.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Autor(a)

Reed Williston

Membro desde: 26/09/12

34 Reputação

0 comentários