How to Reset the Mainboard in your Framework Laptop 16

Escrito Por: Alex Diaz-Kokaisl

Comentários: 0

How to Reset the Mainboard in your Framework Laptop 16

Dificuldade

Easy

Passos

Tempo necessário

5 - 10 minutes

Introdução

Follow this guide to reset the Mainboard in your Framework Laptop 16.

Resetting the Mainboard will set the Laptop's BIOS settings to their factory default. This might be necessary if you want to revert an unsuccessful overclock, if your laptop isn't detecting newly installed memory or storage, or if you're doing general troubleshooting and want to rule out a corrupted BIOS setting.

This procedure is irreversible. Make sure you have your BIOS settings documented if you want to restore them afterwards.

Ferramentas

Framework Screwdriver

Passo 1

Unplug all cables and fully shut down your laptop.

Passo 2

Use your fingers to slide the Touchpad Spacer toward the bottom edge of the laptop and unclip it.
If you're having trouble, check if the corresponding Input Module latch is properly unlocked.
Lift the Touchpad Spacer off the laptop and remove it.

Passo 3

Repeat the same procedure for the other touchpad spacer.

Passo 4

Use your fingers to slide the Touchpad Module toward the bottom edge of the laptop and disconnect it.
If you're having trouble, check if the Input Module latches are properly unlocked.
Lift the Touchpad Module and remove it.

Passo 5

The keyboard is held in place with strong magnets. Apply gradually increasing force to avoid having the keyboard violently eject.
Grip the two pull tabs along the bottom of the keyboard and lift until its magnets release.
Remove the keyboard.

Passo 6

Your Input Module(s) might be different, but the procedure to remove them is the same.
Grip the pull tab at the bottom of the Input Module and lift until its magnets release.
Remove the Input Module.
Repeat for any remaining Input Modules.

Passo 7

Grip the black pull tab on the Mid Plate cable press connector.
Lift up to disconnect the Mid Plate cable.

Passo 8

The Mid Plate screws are ordered from 2–17 (number 1 is the press connector). You don't have to follow the order, but you can use it to help keep track of the screws you've loosened.
Use your Framework Screwdriver to loosen the 16 captive T5 Torx screws securing the Mid Plate.

Passo 9

Use your fingers to lift the Mid Plate off the laptop and remove it.

Passo 10

Plug the laptop into a power source.
The red status LED near the right Expansion Card slots should blink continuously. If this LED isn't blinking, the laptop isn't receiving power correctly—try another USB-C port.
Don't proceed unless the LED is blinking.

Passo 11

Locate the chassis open switch below the memory.
This switch is a sensor that detects if the Mid Plate has been removed. It's a small silver block with a black toggle tab.

Passo 12

Use your finger or the flat end of a Framework Screwdriver to press the chassis open switch 10 times:
Press and hold the switch down for two seconds.
Release the switch and wait for the indicator LED to resume blinking.
Repeat the process 10 times total.

Passo 13

Congratulations on completing disassembly! The remaining steps will show how to reassemble your Framework Laptop.

Passo 14

Place the Mid Plate on the laptop, making sure it sits evenly on its alignment pegs.

Passo 15

Use your Framework Screwdriver to tighten the 16 captive T5 Torx screws in order (starting with 2) to secure the Mid Plate evenly.

Passo 16

Align the Mid Plate cable press connector over its socket and press down to connect it.

Passo 17

Your Input Module(s) might be different, but the procedure to remove them is the same.
Align the top edge of the Input Module with the top edge of the laptop.
Lay the Input Module on the laptop and let the magnets pull the keyboard into place
Make sure the Input Module is seated properly on its alignment pegs and sits flush with the edges of the laptop.
Repeat for any remaining Input Modules.

Passo 18

Align the top edge of the keyboard with the top edge of the laptop.
Lay the keyboard on the laptop and let the magnets pull the keyboard into place
Make sure the keyboard is seated properly on its alignment pegs and sits flush with the edges of the laptop.

Passo 19

Place the Touchpad Module flat on its cutout so its clips are properly aligned.
Press the Touchpad Module down and slide it into place so it lines up evenly with the bottom edge of the laptop.

Passo 20

Place the Touchpad Spacer over its spot on the laptop with the bottom edge overhanging slightly.
Slide the Touchpad Spacer towards the top of the laptop to secure it.
Repeat the same procedure for the other Touchpad Spacer.