Honda S2000 VTEC Solenoid Upper Replacement

Escrito Por: Angeljauregui
  • Comentários: 0
Honda S2000 VTEC Solenoid Upper Replacement

Dificuldade

Easy

Passos

9

Tempo necessário

5 - 30 minutes

Introdução

The VTEC solenoid controls oil pressure to the camshaft's high-lift lobes, allowing Honda's VTEC system to operate correctly. When the upper VTEC solenoid gasket fails, it can cause oil leaks, error codes, and poor engine performance.

This guide will show you how to replace the upper VTEC solenoid on a Honda S2000 using basic hand tools. The process is straightforward and takes only a few minutes. Follow each step carefully to avoid damaging the electrical connector or over tightening the mounting bolts.

  1. KSVKvqHMrfwOwebG
    KSVKvqHMrfwOwebG
    jQPbHaMw6LYNB5xT

    • Open the hood and locate the VTEC on the front left side of the engine, near the valve cover.

    • Clean the surrounding area to keep dirt out of the engine during removal.

  2. FZCXEjw2FLhH1kNO
    FZCXEjw2FLhH1kNO
    Nj1DdwyJQR4PSCYw
    WbofaYLu2mLAB4Vk

    • Locate and remove the three 10 mm bolts securing the upper solenoid.

    • Keep the bolts organized and be careful not to drop the wire attached by one of them.

  3. c6qfEVAjWBcKNWKh
    c6qfEVAjWBcKNWKh
    y5jSIoMfMYLvBfo4
    JlRLAyRv2gASlqDi

    • Lift the electrical connector upward to remove it from the cable holder.

    • Disconnect the two wiring plugs and move the cables aside

  4. DgelDZ1M4VhuJ3DJ
    DgelDZ1M4VhuJ3DJ
    RPKB4qldS63lQWu1
    UjjgtFWiChw4hQ2L

    • Remove the metal cable holder and set it aside.

    • Pull the upper VTEC solenoid straight off.

    • Some oil may drip; this is normal but have a rag ready to catch it.

  5. MNQrZT5DMvPKk3mo
    MNQrZT5DMvPKk3mo
    luhDMeuNY5uB4f3o
    dcrjFILdqLaDNiZI

    • Prepare the replacement solenoid.

    • Insert the gasket (new or used if still in good condition) into its slot.

    • A gasket is a flexible material that is used to make a seal between two connections. This prevents leaks between the two surfaces.

    • Lightly coat it with fresh oil to ensure a proper seal.

  6. pPXFmrhGpCoDlp5v
    pPXFmrhGpCoDlp5v
    VXGiHm2KUsGiFFQL

    • Place the new upper solenoid onto the housing and align it with the bolt holes.

  7. lP6taWjQ56tGtMjy
    lP6taWjQ56tGtMjy
    vkkNlv1WORNFepnx
    WoF1ZhGmyxaZEFqw

    • Reinstall the metal cable holder.

    • Hand tighten all three bolts.

    • Make sure the holder sits straight.

  8. pyEZDXdWVEgYOkVh
    pyEZDXdWVEgYOkVh
    stZUristgbgCSb51
    lPWJEm1GXJXlrSAj

    • Tighten all 3 bolts with a ratchet carefully.

    • Do not overtighten as you can strip the bolts.

    • Reconnect the electrical plug and clip the cable back onto the holder.

  9. XKVvjGlQomhBEGMY
    XKVvjGlQomhBEGMY
    1IY6qUoWK52jJk6C

    • Wipe down the edges where the two parts meet to pick up any oil that may have spilled.

    • Keep an eye on the solenoid for any oil leaking after cleaning.

Conclusão

Congratulations! You now have a properly working VTEC solenoid. Be sure to keep an eye on the solenoid in case of any oil leaks.

Autor(a)

Angeljauregui

Membro desde: 13/03/24

169 Reputação

0 comentários