HP Spectre x360 13-ac023dx Display Replacement

Escrito Por: Jonathan
  • Comentários: 6
HP Spectre x360 13-ac023dx Display Replacement

Dificuldade

Moderate

Passos

7

Tempo necessário

25 - 40 minutes

Introdução

This guide will show you how to replace the display of your HP Spectre x360 Spectre 13’’ (Model: 13-ac023dx).

Hazard: Ensure you turn off your device before starting.

  1. 1MhkVSDsny3TRWKG
    1MhkVSDsny3TRWKG
    eRH63AJPBF1ptHMb

    • Flip the laptop over so the model sticker faces the ceiling.

  2. JupkD6Zp6H3oNlbi
    JupkD6Zp6H3oNlbi
    T41fwcLomOIKvMQ1
    RGJjuJhSoQWBIdke

    • Use a Torx #5 screwdriver to remove the six 3.5 mm screws holding the back cover to the laptop.

    Was eine dämliche Konstruktion, Schrauben unter Füßen zu verstecken!!!

    Dirk S. -

    You do not need to remove the bottom ones closer to the trackpad since there are no screws under there.

    To remove the top ones by the hinge they are glued in so you need to pry under them with a pick.

    When pulling out the panel pull from the side closer to the hinge or you risk breaking the plastic on the panel where the hinge is. I think it just keeps out dust but need to be careful when removing it.

    Hamza Syed -

    Die Angaben zu den Schrauben sind nicht korrekt. Es müssen 6 Torx-Schrauben gelöst werden. Diese befinden sich aber nicht under den Füßen, sondern sind alle ohne weitere Schritte sichtbar und zugänglich (Die Markierungen im Foto sind nicht korrekt platziert). Zusätzlich befinden sich zwei Philips-Schrauben unter den Füßen an der Gelenkseite. Die Füße erst mit einem Föhn vorsichtig erwärmen und dann mit einem Öffnungswerkzeug abhebeln.

    Robert -

  3. qLEJDnAKgHKcl5jJ
    qLEJDnAKgHKcl5jJ
    xJPapt5LQDGWUPoW

    • Use the Phillips #000 screwdriver to remove the four 3.5 mm screws holding the battery.

    • After removing the screws, detach the battery wire from the mother board with the iFixit opening tool.

    • Then, carefully lift the battery off with the iFixit opening tool.

    Need to provide a direction in step #1 about removing the rubber pads and accessing the two screws at the bottom.

    David McCurry -

    Second that. What's the best way to remove the feet?

    Oskar Petersons -

  4. VIFodGDELESJWsaP

    • Lay the laptop flat on the table with the keyboard side facing the table and the motherboard facing up.

  5. aSgM23YXEgf5QvT1
    aSgM23YXEgf5QvT1
    oZSwWlLUWyV4ZGDg
    btuBX452JGU4jdHG

    • Using the Phillips #000 screwdriver, remove the four 1.0 mm screws that attach the display to the main body of the computer.

  6. PGSv5jnP1HPLkCOl
    PGSv5jnP1HPLkCOl
    nxH14VSUnTRxv5eV
    gkWQGrZcwDZWPoA4

    • Move the metal components that were just unscrewed out of the way to make a clear view of the two display connectors.

    • Flip up both latches that are found at the center of the computer's body where the wires connect to the motherboard. Then release the wires that attach to the display. This will separate the two main parts of the computer.

  7. HvEVOQT2yJrRlVHq
    HvEVOQT2yJrRlVHq
    Q2R3iNiOpGf22RZi

    • Separate the display from the bottom half of the computer(motherboard).

Conclusão

To reassemble your device, follow these instructions in reverse order. Take your e-waste to an R2 or e-Stewards certified recycler.

Autor(a)

Jonathan

Membro desde: 21/10/19

498 Reputação

Um comentário

I couldn’t remove the display without removing the one speaker. In the pictures, you can easily see that he just bent the metal case at the hinge and pried it out.

Ryan Stauffer -