Google Pixel 10 Pro Fold Back Glass Removal

Escrito Por: Alex Diaz-Kokaisl
  • Comentários: 0
Google Pixel 10 Pro Fold Back Glass Removal

Dificuldade

Moderate

Passos

9

Tempo necessário

No estimate

Introdução

  1. oLQaIT4WVlTeFgkw
    oLQaIT4WVlTeFgkw
    XaHKwLwvrq2GsXmI
    w1WcPR14G3FMxxiS

    • Apply a suction cup to the back cover, as close to the center of the bottom edge as possible.

    • While securing the phone with one hand, pull up on the suction cup with strong, steady force to create a gap between the back cover and the frame.

    • Insert an opening pick into the gap.

    • If your back cover is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken back cover.

  2. parBUNVugVMe1D5r
    parBUNVugVMe1D5r
    oKb34OxbhDpBhAkZ
    Gnnane2VwKHtbVlv

    • The adhesive along the right edge of the back cover is thicker than the rest. You'll need to insert your opening pick at a minimum of 4 mm to separate the adhesive.

    • Remove the suction handle from the back cover.

    • Slide the opening pick around the bottom right corner and up the right edge of the back cover to separate the adhesive.

  3. WZaK2yNa2jygLGDt
    WZaK2yNa2jygLGDt
    4T1vNHsVYDwhu6av
    rnqMipJS4WsmMDRh

    • During the next two steps, don't insert your opening pick deeper than 3 mm to prevent damaging the metal springs around the frame.

    • Optionally, you can measure and mark your opening pick at 3 mm to help you visualize the length.

    • Continue sliding the pick around the top right corner and across the top edge of the back cover.

  4. 3onM4LUiQPUgSSmK
    3onM4LUiQPUgSSmK
    gItqLExkfOhqbCCC
    XVSMgm4uEfDKs336

    • Slide your pick down the left edge and around the bottom left corner to separate the remaining adhesive.

  5. gXhkZFEgEQHkBKGw
    gXhkZFEgEQHkBKGw
    VvcYaS5OBKXqesUZ
    nG4OYpYelyOYGIFF

    • Don't fully remove the back cover yet, as it's still connected to the phone by a cable.

    • At this point, the back cover should be free from the frame. If there's still resistance around the edges, use an opening pick to separate any remaining adhesive.

    • Lift the right edge of the back cover and swing it over the left edge of the phone.

    • Prop up the back cover with your suction handle or a clean, sturdy object, making sure that the cable isn't strained.

  6. asjTT4EiM1NVNOPk
    asjTT4EiM1NVNOPk
    EIZoYBpcNYBKAh3a

    • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.

    • While the Pixel 10 Pro Fold uses Torx Plus screws, standard Torx bits also work. Use the same size or one size larger (T3 or T4 Torx bits with 3IP Torx Plus screws) and apply constant, downward force to prevent stripping.

    • Use a Torx Plus 3IP driver to remove the three 3.0 mm‑long screws securing the top bracket.

  7. hXLoqHcqIyuiQwnQ
    hXLoqHcqIyuiQwnQ
    nmixLhNhqyPWZjrk
    sx32S4oR2CnRd4aZ

    • Use the point of a spudger to pry up the top bracket and release its clip from the top edge of the frame.

    • Remove the top bracket.

  8. Z5HWORueTJoUsr4a
    Z5HWORueTJoUsr4a
    ysGIiQXFUO16jxUQ

    • When disconnecting press connectors, pry only at the gold outlines on the logic board.

    • Don't insert your spudger anywhere else, as you risk dislodging surface‑mounted components.

    • Use the point of a spudger to pry up and disconnect the back cover cable.

  9. CmIoREmGyQ2rtPQQ

    • Lift the back cover off the frame and remove it.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Autor(a)

Alex Diaz-Kokaisl

Membro desde: 16/01/22

227430 Reputação

0 comentários