George Foreman GRS040BC Disassembly

Escrito Por: Reika Nakagawa
  • Comentários: 0
George Foreman GRS040BC Disassembly

Dificuldade

Easy

Passos

13

Tempo necessário

10 minutes

Introdução

The George Foreman GRS040BC is a 10.5" by 7.5" portable double-sided electric grill with a black exterior and a brown/tan grill tray interior. It has a single power cable that turns the device on and off, indicated by a red and green light.

  1. UJBmyQYHOU6GwPjP
    UJBmyQYHOU6GwPjP
    cUFlCmVO2dHdEjQM

    • Open the lid of the grill.

  2. oyLl5pD1fACU4EdT
    oyLl5pD1fACU4EdT
    skFfGXPn13IWZ5Iv

    • Remove the two 10 mm screws that secure the left hinge to the top panel of the grill using a Phillips #2 screwdriver.

    • The left hinge will completely detach from the device.

  3. R5ZIvVqp6H4Nl2CC
    R5ZIvVqp6H4Nl2CC
    JPygTCPaWfpRnFMW

    • Remove the two 10 mm screws that secure the right hinge to the top panel of the grill using a Phillips #2 screwdriver.

    • The right hinge will not fully detach from the device.

    • Do not attempt to pull the two panels apart as the right hinge houses power cables that run between the top and bottom grill panels.

  4. V5FEMkSJWKET4sAG

    • Remove the four 10mm screws that secure the top grill tray to the black backing using a Phillips #2 screwdriver.

  5. vXwC26pMjxZkON3B
    vXwC26pMjxZkON3B
    t6hWBB5SBmePGN5N

    • Gently remove the top grill panel from the back casing to reveal the wiring and heating system.

  6. 1QGKnfsZGKMX3HKS
    1QGKnfsZGKMX3HKS
    tiD46F13ZdsKTiGf
    4WIuDeUZZUEJXhcG

    • Please note this step is OPTIONAL! Reassembling the thermistor is difficult, so do not unscrew this unless it's completely necessary

    • Remove the two 5mm screws from the thermistor using a Phillips #2 screwdriver.

    • Remove the thermistor.

  7. vQQJ1EFvPpJMNH35
    vQQJ1EFvPpJMNH35
    dkHPsAUMXEKXTTkf
    oefRH4aasppOKYBS

    • Please note that this step is OPTIONAL. The lights can be difficult to reassemble, so only do this if you have issues with the lights that you need to fix.

    • Remove the three 7.5 mm screws found on the black covering.

    • Take the cover off to show the lights.

    • When reassembling, squeeze the bulbs back into place, ensuring that you put the red and green covers in the correct configuration. Press the split wires down on each side of the red/green lights and screw the black cover back on.

  8. TWADJLwE3f5K1y3R
    TWADJLwE3f5K1y3R
    fbstcvRDHffrTOr1

    • Close your partially disassembled George Foreman and turn it upside down.

    • Pry out the two rubber supports.

    • Lift the back stand on the bottom of the device.

  9. M52MLxOACivSx3UD
    M52MLxOACivSx3UD
    KnU1YQ2MR1JKJAtS
    R5n2WICGjcmBVHO4

    • Remove the four 10mm screws found deep beneath the rubber supports and in the opposite corners.

  10. uV2TklcQGUEsMC22
    uV2TklcQGUEsMC22
    ZFLM6HbYaOxbR4vj
    eghuIfwDySHK1rTU

    • Gently open the bottom case, taking caution not to mix up or break any wires.

  11. LWEoA2vIrfSkbNkr
    LWEoA2vIrfSkbNkr
    WGJ3fZS4Lf4krHYo
    dYvtPhmApoJU6OOg

    • This step is also entirely optional.

    • Remove the 5mm screw connecting the white cable to the grill.

  12. I6cSC2EhCQTbeKXl
    I6cSC2EhCQTbeKXl
    KgvCO31ssAMCflQv

    • Remove the two 12mm screws found on the casing under the black stand using a TR6 Torx screwdriver.

  13. hxqKTCfDHWRUw5GF
    hxqKTCfDHWRUw5GF
    PIMmiKeZ4TJrfwJZ

    • Remove the casing and the stand, which will clip off, to reveal the wiring.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Autor(a)

Reika Nakagawa

Membro desde: 13/09/25

217 Reputação

0 comentários