Behringer BCD3000 Disassembly

Escrito Por: Tobias Isakeit
  • Comentários: 4
Behringer BCD3000 Disassembly

Dificuldade

Moderate

Passos

11

Tempo necessário

No estimate

Introdução

  1. FJ2FJELAX1rmbjej

    • Unplug from all cables

  2. 62LnYcDOY4NIVtNM
    62LnYcDOY4NIVtNM
    OD1GPkBmK4h4MVMZ

    • unscrew two Phillips screws on each side of the BCD3000

    • If the screws sit too tight, you can use the extension for better torque

  3. 6LP5QTR1yAYT4nxO
    6LP5QTR1yAYT4nxO
    ZTEZPiDpOp1iRtUe

    • unscrew another two Phillips screws on each side

  4. fZDfUAQuVDXJLwpn
    fZDfUAQuVDXJLwpn
    ZIlZ6ZTwJHNAxODu
    WBKvB5hN4VCAYU6i

    • Lift the upper control part.

    • Be careful, there are still some cables connected to the lower section.

    • Disconnect the cables by walking them out of their sockets.

  5. 3bmkbAYmF2o2yGIS

    • Remove the upper part completely.

  6. O4VWvoVL2KFSJYSt

    • Disconnect the two cables from the lower section to the connector board.

  7. CaGxAtovX5fPersV
    CaGxAtovX5fPersV
    2ccXEYjDaVxKuPsM
    mTyMRwNnHCUi3vWO

    • Slide the lower section to the front.

    • Now you can lift it and take it aside.

  8. KyqlNselWKafwbIo
    KyqlNselWKafwbIo
    IrilvRTnxOGtg1lM
    64fIxssdxxPmR4va

    • Disconnect the separate boards.

    • Now you can take the modules out by unscrewing them from the case.

  9. VQXc4JmCqMM2GRZH
    VQXc4JmCqMM2GRZH
    I1DmUjaA4NFhVpBK

    • The jog wheels on the front panel can be taken off by using a spudger and levering them out.

  10. ceOwOJpQCGFRPOHR
    ceOwOJpQCGFRPOHR
    neUSPaxeBh6KnqKO

    • The knobs can easy be removed just by pulling.

  11. HplwlMWKDteIY2EK
    HplwlMWKDteIY2EK
    1P6bnPChNRlBLMMg
    j3Aoou5hZh3VoYIq

    • Same goes for the knobs on the top section of the front panel.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Autor(a)

Tobias Isakeit

Membro desde: 31/03/14

131341 Reputação

4 comentários

Pensaba que serviría para la BCD2000… pero es algo distinta.

Antonio -

great stuff, with better quality pictures would be better

csipapicsa -

This is great! I thought it would be like the other BC controllers (BCR/BCF2000) with a clip on the side panels. I need to re-seat my knob rings that have gotten loose and fallen of the top panel.

NomeX -

Thanks for the guide! I was able to re-glue and re-seat my knob rings that popped loose. I had two on the top section (main vol and FX4) and one at the lower that was working loose, so I decided to hit that one as well since I already had the BDC3000 apart. I find it odd that Behringer used machine screws on the bottom of the machine since they screw into plastic posts. The control knobs rings are held in place with a thin glue that, after nearly 20 years (mine was 1105 date), have weakened and allow easy popping off. I used a glue that didn't melt the pieces together (preferred, but I didn't have), so I may have to go through this process again. When reassembling, take care that the buttons seat properly into the panels as they can wiggle out of place and make screwing the PCBs difficult and reassembly impossible. If you need total disassembly, you'll need a socket wrench or mini pliers to remove the nut from the headphone jack. I don't think this is a necessary step if you're just re-seating/gluing the rings.

NomeX -