Battery Disconnection

Escrito Por: Spencer Day
  • Comentários: 0
Battery Disconnection

Dificuldade

Moderate

Passos

13

Tempo necessário

No estimate

Introdução

This guide shows how to disconnect the battery in your Samsung Galaxy S25 Edge smartphone.

  1. gRrGFHOvnCPGSi14
    gRrGFHOvnCPGSi14
    SIJAOaG1JcTRhyaM

    • Let your phone's battery drain below 25% before starting this repair. A charged lithium-ion battery may catch fire if accidentally damaged.

    • Completely power off your phone and unplug all cables.

  2. AUKgucWQgIw6abYc

    • Mild adhesive secures the back cover. Heating it will soften the adhesive, making it easier to separate.

    • Heat an iOpener and lay it on the bottom edge of the back cover for two minutes to soften the adhesive.

    • Alternatively, you can use a hair dryer, heat gun, or hot plate to heat the cover.

  3. MKZYaKnSqRMOttaV
    MKZYaKnSqRMOttaV
    DYNBmtI5KIlNMVyp

    • Apply a suction handle near the center of the back cover's bottom edge, as close to the edge as possible.

  4. cNHreUvGGgTdMHso
    cNHreUvGGgTdMHso
    FalHG4ZWwBWcXaZ2
    ML4qOdvgkFqeepJZ

    • Pull up on the suction handle with strong, steady force until a gap forms between the cover and frame.

    • Insert the tip of an opening pick into the gap.

  5. pydYLtDqUDE4YDRh
    pydYLtDqUDE4YDRh
    fFkYJ4iEjMtEbSXb
    kuNsiooXAiThndsn

    • The back cover is secured with adhesive around the perimeter of the frame. Use this picture as a reference while you separate the adhesive.

    • When separating the left and right edge adhesive, don't insert your pick more than 3 mm to avoid damaging the wireless charging coil and interconnect cable.

  6. CMsiBVBI5kwUqXOW
    CMsiBVBI5kwUqXOW
    VaLGN3iKlVVhUCTk
    e4nGGwSexGxYRagn

    • If you have trouble separating the adhesive, apply more heat and try again.

    • Slide your opening pick along the bottom edge to separate the adhesive securing the back cover.

  7. MQxHqTLKpfOwLQHC
    MQxHqTLKpfOwLQHC
    HMS5xDmgPWIZRwFn
    D2ndMNVjVM6vdnfd

    • Continue sliding your pick around the entire perimeter of the back cover to separate all the remaining adhesive.

    • Remember not to insert your pick too far under the long left and right edges.

  8. cCmWGpNnHEs2Rds1
    cCmWGpNnHEs2Rds1
    EkOvtCDKRdXTSqrj

    • Remove the back cover.

    • If you're having trouble, check the perimeter for any remaining adhesive and use your opening pick to separate it.

    • During reassembly:

    • This is a good point to power on your phone and test all functions before sealing it up. Be sure to power your phone back down completely before you continue working.

    • Check your rear cameras for any smudges and gently wipe them with a clean lint–free cloth if necessary.

    • Your replacement back cover adhesive will be applied to either the frame or the back cover. Use cutouts and contours to see where it lines up best. If it matches the back cover, follow this guide. If it matches the frame, use this guide.

  9. 1fRv1fV12gvcDQbb
    1fRv1fV12gvcDQbb
    WGwxhlnuWIRjQlWO

    • Use the point of a spudger to pry up and disconnect the wireless charging assembly press connector from its top edge.

    • Getting the spudger under the connector can be tricky. If you're having trouble, try using the tip of an opening pick instead.

  10. ZZ1TYFCZd2h4SEZc
    ZZ1TYFCZd2h4SEZc
    JuGasFR5i21jcCYp
    BCZUXmlCiDnQFVlJ

    • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.

    • Use a Phillips screwdriver to remove the eleven 2.8 mm‑long screws securing the wireless charging and loudspeaker assembly.

  11. rIxbjnIn2FM1BFZs
    rIxbjnIn2FM1BFZs
    3MbR2OPK56ovnDDG
    YZwsHeR1ZBXyLiDo

    • The wireless charging coil is connected to the loudspeaker with delicate tape. It's easiest to remove the coil and loudspeaker together as one assembly to avoid damage.

    • Use angled tweezers to pry up and unclip the loudspeaker by the notch on its left edge.

    • During reassembly, press down firmly around the perimeter of the loudspeaker to engage its clips.

  12. D1kANNWXUXwMu6XG
    D1kANNWXUXwMu6XG
    koJQCO1JHnoDu2me

    • Use two hands to lift and remove the wireless charging and loudspeaker assembly.

  13. LWh51vKjKZUN2viw
    LWh51vKjKZUN2viw
    MTSMykZjgmxSLPtU

    • Every press connector has a corresponding gold arrow on the board that shows the proper location to pry—nifty! Prying at the wrong location risks damaging the fragile surface‑mounted components on the board.

    • Use the point of a spudger to pry up and disconnect the battery press connector.

Autor(a)

Spencer Day

Membro desde: 14/09/22

165254 Reputação

0 comentários